Jeep Check Engine Light

Jeep Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several common causes including something as simple as a loose gas cap. Other mainly common reasons for a Check Engine Light are a malfunction with the fuel injection system, damaged oxygen sensor, defective head gasket, defective emissions control part, dirty mass airflow sensor, or damaged spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Jeep Certified Technicians and the certified service protocol to isolate the root problem and utterly repair it as required to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Jeep issue was entirely fixed.

Every Jeep was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its critical systems. The fast sensors are continually detecting conditions while sending critical data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, sadly that is the limitation of the Check Engine Light – it won’t tell you what explicitly is wrong nor what to do about it. That’s where we come in; Larry H. Miller Chrysler Jeep Dodge Ram Provo provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Exceedingly Qualified Service professional.

What could cause the check engine light to come on in a Jeep?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Again, the check engine light could still be a warning of an essential problem that could cause serious damage to your engine and come with a hefty and expensive repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady and continuous glow generally means something less serious but a flashing check engine light indicates that your vehicle’s engine is in significant trouble and helpful service is necessary rapidly. If your check engine light is flashing in your Jeep, we very endorse not to drive the vehicle and schedule Jeep service today. Below is a list of the most common reasons your check engine light can come on:

• Your Jeep has a vacuum leak. Each Jeep has a vacuum system that performs a wide variety of functions. The vacuum system again helps lower unhealthy emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, exceptionally if they’re exposed to intense heat or extreme cold.
• Your catalytic converter is bad or going bad. The catalytic converter is a part of your Jeep ’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is ordinarily caused by constantly neglected maintenance, which is why Larry H. Miller Chrysler Jeep Dodge Ram Provo offers a free multi-point check with each Jeep service. If you have an issue with your catalytic converter and don't get it repaired, your Jeep will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other delicate problems from overheating.
• Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns more expeditiously and your car will be less efficient when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A broken sensor can not only affect your miles per gallon, but it can cause serious damage to your catalytic converter and your Jeep 's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to determine the precisely correct mix of air and fuel that enters the cylinders in your engine. A broken O2 sensor can again cause a car to fail an emissions test.
• The battery is low or dead. The battery in your Jeep is each crucial. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Jeep you drive, but check our current service coupons and specials.
• One of the most common and frequent cause is that your Jeep gas cap is loose, damaged or missing. The gas cap for your Jeep serves different purposes. It prevents dangerous gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a broken fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump and be more expensive. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on swiftly after you put gas in your Jeep, first thing you should check is to make sure the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
• New Spark Plugs or Plug Wires are needed for your Jeep. The spark plugs are the part of your engine that ignites the air/fuel mix in the combustion chamber of your car. This explosion is what moves the pistons and makes the engine run smooth. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience a conspicuous poor performance and decreased power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, leading to more expensive repairs.
• Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Jeep is what determines how much fuel is needed to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to certain changes, like altitude. If your Jeep is having trouble starting, idling rough or has a sudden fast change in the position of the throttle pedal, this could be a critical sign of a broken mass airflow sensor.
• Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak extreme havoc on your Jeep if it’s not installed correctly. These aftermarket components and accessories can drain the battery, trigger the check engine light, or even prevent the car from starting. If these issues sound familiar, bring your to Jeep and have our team of accomplished certified mechanics assure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, exceptionally aftermarket parts and accessories, or utilizing OEM components first place might cost a little bit more but could help you save substantially from having to get poor work and damage caused by poor installation work corrected.

Jeep Check Engine Light Codes

The check engine light turning on can be quite intimidating, especially to see that little light on your vehicle’s dashboard suddenly illuminate, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, again known as the OBD (on-board computer diagnostic system) in your. There are hundreds of different codes that your check engine light can correctly represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you helpful knowledge about your car and will again allow that vital Check Engine Light to do what it is genuinely supposed to do: be your guide. Unfortunately, clear and helpful car symptoms do not regularly accompany an illuminated Check Engine Light. Since there are hundreds of imaginable OBD codes, there are again hundreds of imaginable reasons for the light, including:

• Loose Gas Cap or Missing Gas Cap
• Bad Spark Plugs
• Emissions controls issues
• Transmission issues
• Ignition system faults
• O2 Sensor
• Fuel and air metering systems problems
• Old Battery
• Computer output circuit issues

This is why it is crucial for someone who does not have a lot of prevalent automotive knowledge to not assume what a code means. When your check engine light comes on, you should get it checked out quickly by a talented certified Jeep mechanic. If the engine light comes on due to a serious concern, you risk damaging your vehicle further by not repairing the issue right away. Call Larry H. Miller Chrysler Jeep Dodge Ram Provo at 8446668361 today or schedule your check engine light service online today!

Will the check engine light reset itself?

The check engine light on your Jeep will normally shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will swiftly turn itself off. Also, if your catalytic converter is working correctly, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Jeep light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Larry H. Miller Chrysler Jeep Dodge Ram Provo so the light and code can be double-checked and reset.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your Jeep is the check engine light. The check engine light is part of the vital onboard diagnostics system, and displays in an assortment of different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your car. Onboard computers increasingly have controlled and monitored car performance since the 80s and do an assortment of things for your Jeep. Some of these essential duties include ignition timing, controlling engine speed, shifting automatic transmissions and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of different things. It can be as simple as your gas cap being loose or as perilous as engine knocking. If your check engine light is on in your Jeep, contact Larry H. Miller Chrysler Jeep Dodge Ram Provo. Contact Larry H. Miller Chrysler Jeep Dodge Ram Provo today! Our Jeep service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing.

Check Engine Light Service Jeep

What do you do when you’re driving along in your Jeep and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Jeep owners, your heart sinks extremely because you may have specifically idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep, peaceful breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is advised that you get your Jeep checked expeditiously. Ignoring that warning could end up causing major, major damage to pricey engine components.

When your Jeep 's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is usually labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that can immediately identify the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Jeep auto repair mechanics at Larry H. Miller Chrysler Jeep Dodge Ram Provo. There are also a number of comparatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the absolutely correct issue and repair it.

Is it safe to drive your Jeep with the check engine light on?

This question is not extremely simple because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is usually indicated by a steady glow of the check engine light. If you notice a difference in the performance of the car, it could be an indication of a more serious problem. If the check engine light is flashing, this means that there is a serious issue and it is recommended to service your Jeep immediately. Call the experts at Larry H. Miller Chrysler Jeep Dodge Ram Provo by dialing 8446668361 so you can describe the issues. Or reduce your speed and bring your Jeep to our certified mechanics as soon as likely.

How many miles can you drive with the check engine light?

It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we recommend that you pull over and contact Larry H. Miller Chrysler Jeep Dodge Ram Provo to help determine if your car is secure to drive in or if we recommend a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. Since each check engine code has its own level of severity, it is ordinarily difficult to predict how many miles you can be secure in driving with the warning light on.

Jeep Check Engine Light

A flashing light signifies that the problem is exceedingly serious and if not taken care of quickly may result in major and meaningful damage to the vehicle. If the check engine light in your Jeep starts flashing, that means that the problem needs attention quickly and your Jeep should be brought in expeditiously. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can expeditiously raise the temperature of the catalytic converter to a point where damage is likely, requiring an pricey and huge repair. Some owners ask if spark plugs cause the check engine light to flash? This can explicitly be the cause. A defective, old or dirty spark plug can cause the engine to misfire. If your check engine light is regularly flashing, please contact our team of automotive experts at Larry H. Miller Chrysler Jeep Dodge Ram Provo quickly by calling 8446668361. If the problem is completely ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is ordinarily between $88 and $111. The good news, Larry H. Miller Chrysler Jeep Dodge Ram Provo offers completely free multi-point inspections and free diagnostics, in most cases, to help determine the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more serious failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it good to get the proper code reading and diagnosis.